The article guide will walk you through the simple steps to login and manage your extender. In which you can adjust settings, update firmware, or monitor its performance. Let’s get the access through the computer interface via mywifiext.
Before Setting Up Your Extender
ü Connect extender with the router Via cable
You can use the cable to the connect the router with the
router first and then then try to configure the device. The cable should
connect in the router’s LAN port and extender’s Ethernet port.
ü Connect extender with the router Via WPS
1.
Look for a button on your main wireless router
labeled WPS.
Note: Netgear extender should plugged into a power outlet
and is powered on.
2.
Locate the WPS button on your router and press
it briefly.
3.
Never hold it down for too long. A short press
is sufficient.
4.
Give a gentle push to WPS button on your router.
Find the WPS button on your Netgear Wi-Fi extender and press it as well.
5.
WPS button location on extender can be vary on
the model, so you should consult your extender's manual if you're unsure. It's
often on the side or front of the device.
After pressing the buttons, you must allow a few seconds for
the WPS process to complete. While WPS is online, you should see the WPS or
Wi-Fi status LEDs on both the device blinking. When the connection is
successful, the LEDs should become solid.
ü Where to place your extender
You should place the extender
close to the router during the WPS connection. When it connects, you can unplug
the extender to a location roughly halfway between your router and the dead Wi-Fi
coverage. Plug it back in and allow it to reconnect.
STEPS TO CONFIGURE AC1200
ü Connect computer with the extender
In the situation, you want to link your computer or laptop
with your Netgear extender network, you can use default network SSID
credentials.
The network name usually in a format like NETGEAR_EXT. You
will find the default Wi-Fi network name and password on a label on your
extender.
In case of wired connection, connect a computer directly to
your extender using an Ethernet cable.
ü Access the Mywifiext login page
·
Launch any web browser on your connected device.
·
In the address bar, type one of the following
and press Enter: mywifiext.net (for
Windows PC)
·
Or enter the Login URL mywifiext.local (for Mac
OS)
·
Or use the 192.168.1.250 (default IP address for
Netgear extenders)
·
You should be redirected to a login page for
your Netgear extender.
·
Enter your username and password. The default
username is often "admin," and the default password is
"password." However, if you've previously changed these, use your
custom credentials.
·
Click "Log In" or a similar button.
ü Adjust the settings and features
Now, you will log in to the device
and can adjust any of the setting of the extender and make the choice of the
network you need in your house.
You should run below given tips to make the network secure
and resolve the problem if you get any from the extender side:
Troubleshooting tips and solutions
1.
Ensure your device is properly connected to the
extender's Wi-Fi network or via an Ethernet cable to the extender.
2.
Try restarting your modem, router, and the
Netgear extender. Then, try accessing mywifiext again.
3.
If all else fails, you might need to factory
reset your Netgear extender. Look for a small reset button (usually a pinhole)
on the extender, press and hold it for about 10 seconds with a paperclip or
pin, and then try the Netgear
WiFi extender setup process again.
4.
Make sure the typed address is correct. It
should be either mywifiext.net (if using Windows PC), mywifiext.local (if using
iOS device), or 192.168.1.250 (for any) into the browser's address bar, not a
search engine.
5.
Try the login process after updating your
computer’s web browser. To update:Go into the browser settings. Select the
About option. Click Check for UPDATE or UPDATE.
Note: Sometimes old browser data can interfere. Clear
your browser's cache and cookies and try again. If one browser isn't working,
try using a different one.
The Conclusion
To log into your AC1200 WiFi extender, ensure your device is
connected to its network, then navigate to mywifiext.net or its IP address in a
browser. Use your admin credentials to access settings and manage your extended
network.
